Foro

Bienvenido al Foro de zonafpv.com, poco a poco estamos mejorando el sistema, para participar en el foro hay que empezar por este hilo:

u360gts: Seguidor d...
 
Comparte:

u360gts: Seguidor de Antena de Rotación contínua 360º  

Página 6 / 8
  RSS
RomanF
(@romanf)
Principiante

 

FoMa Systeme GmbH

ResponderCitar
Respondido : 13/08/2019 9:24 am
RomanF
(@romanf)
Principiante

Ok! 

I'm sending files again
thank you

.

FoMa Systeme GmbH

ResponderCitar
Respondido : 13/08/2019 6:33 pm
RomanF
(@romanf)
Principiante

Note: These are the same 2 files uploaded twice (Name Setup  has different)

FoMa Systeme GmbH

ResponderCitar
Respondido : 13/08/2019 6:36 pm
rortega
(@rortega)
Miembro Moderator

Nos complace presentar el configurador u360gts de próxima generación, completamente renovado, que mejorará en gran medida la experiencia del usuario, gracias a la valiosa contribución de Hector Narbona.

Esta nueva versión es compatible con las familias de firmware u360gts 9.xy 10.x, sin embargo, algunas características como el indicador de estado del GPS podrían no funcionar correctamente con ellos, y serían totalmente compatibles a partir de la versión 11.

https://github.com/raul-ortega/u360gts-configurator/releases/tag/4.0

ResponderCitar
Respondido : 14/08/2019 1:14 am
rortega
(@rortega)
Miembro Moderator

@romanf

This is what I get from your log file (2307 records):

 

Sats/Lat/Lon/Alt: 13 49501788 11252276 -1
Sats/Lat/Lon/Alt: 13 49501788 11252276 -1
Sats/Lat/Lon/Alt: 13 49501788 11252276 -1
Sats/Lat/Lon/Alt: 13 49501788 11252276 -1
Sats/Lat/Lon/Alt: 13 49501788 11252276 -1
Sats/Lat/Lon/Alt: 13 49501788 11252276 -1
Sats/Lat/Lon/Alt: 13 49501788 11252276 -1
Sats/Lat/Lon/Alt: 13 49501788 11252276 -1
Sats/Lat/Lon/Alt: 13 49501788 11252276 -1

....

Sats/Lat/Lon/Alt: 13 49501797 11252269 0
Sats/Lat/Lon/Alt: 13 49501797 11252269 0
Sats/Lat/Lon/Alt: 13 49501798 11252269 0
Sats/Lat/Lon/Alt: 13 49501798 11252269 0
Sats/Lat/Lon/Alt: 13 49501798 11252269 0
Sats/Lat/Lon/Alt: 13 49501798 11252269 0
Sats/Lat/Lon/Alt: 13 49501798 11252268 0
Sats/Lat/Lon/Alt: 13 49501798 11252268 0
Sats/Lat/Lon/Alt: 13 49501798 11252268 0

...

Sats/Lat/Lon/Alt: 14 49501786 11252263 -1
Sats/Lat/Lon/Alt: 14 49501786 11252263 -1
Sats/Lat/Lon/Alt: 14 49501786 11252263 -1
Sats/Lat/Lon/Alt: 14 49501786 11252263 -1
Sats/Lat/Lon/Alt: 14 49501786 11252263 -1
Sats/Lat/Lon/Alt: 14 49501786 11252263 -1
Sats/Lat/Lon/Alt: 14 49501786 11252262 -1
Sats/Lat/Lon/Alt: 14 49501786 11252262 -1
Sats/Lat/Lon/Alt: 14 49501786 11252263 -1

This post was modified hace 2 meses by rortega
ResponderCitar
Respondido : 02/09/2019 9:03 pm
rortega
(@rortega)
Miembro Moderator

@romanf Roman Foltyn I have checked your configuration file and I have seen something that I'm not sure if it might be related with your problem, but you have to correct something:

mag_calibrated param value is 0, you have to set it to 1. Old configurator version might be the source of this issue, use latest configurator version, calibrate the mag if you did not do it and/or set calibrated as on with the toggle button.

You should dissable DEBUG feture, because this will set your home at Zurich, Switzerland.

feature -DEBUG
save

If the frequency of gps position packets is greater than 2 Hz disable feature EPS.

feature -EPS
save

It seems that selected telemetry baud rate and protocol is ok, so you have to review the configuration of your bluetooth modules, all the devices involved in the communication sould be to set 115200 bauds. Try also enabling featture AUTODETECT:

feature AUTODETECT
save

ResponderCitar
Respondido : 02/09/2019 9:45 pm
RomanF
(@romanf)
Principiante

@rortega

I did everything as you said, the new Configurator 4.0.1 New Firmware (u360gts / NAZE 10.1.3 Jul 31 2019 / 00:07:11 (c444206))
I set the parameters according to your reservations.
Autodedect protocol is ON

Taranis Plus sends CRSF 115200 Baud Stream gets via BT to NAZA.
OLED Display, however, indicates the Mavlink protocol, not CRSF see Picture.

I did not find the protocol setting on CRSF

oled Info

 

FoMa Systeme GmbH

ResponderCitar
Respondido : 03/09/2019 2:34 pm
rortega
(@rortega)
Miembro Moderator

@RomanF I didn't say anything about flashing the board with firmware version 10.1.3.

You have to flash again the experimental version 10.2.

https://github.com/raul-ortega/u360gts/raw/master/other-releases/amv-open360tracker_dev10.2.zip

ResponderCitar
Respondido : 03/09/2019 4:33 pm
RomanF
(@romanf)
Principiante

@rortega

I have NAZE Board and at this address is only "amv-open360tracker_SPRACINGF3.HEX."
I think this is not adapted to NAZE?

Where can I find the NAZE version?

FoMa Systeme GmbH

ResponderCitar
Respondido : 03/09/2019 7:49 pm
rortega
(@rortega)
Miembro Moderator

@romanf

You will find 4 hex files inside the zip:

IMG 20190903 223525

ResponderCitar
Respondido : 03/09/2019 10:38 pm
josean
(@josean)
Principiante

Antes de nada quiero agradecer a Raúl su saludo de bienvenida y comentar que tengo casi todo el material para montar la antena. La controladora que voy a utilizar es una Naze32  con brújula en la cual he instalado el firmware naze 10.1.3. y a partir de aquí comienzan las preguntas:

He intentado buscar como se modifica el servo de pan para que gire libre 360º pero no doy con ello, ¿me podéis indicar como se hace?

Veo que existe una mecánica oficial y entorno a ella se han diseñado o rediseñado otras, ¿Cuál sería en este momento la más sencilla de montar e imprimir?

ResponderCitar
Respondido : 03/09/2019 10:39 pm
josean
(@josean)
Principiante

A la primera pregunta me voy a responder yo mismo, pues acabo de encontrar este post en rcgrups 

https://www.rcgroups.com/forums/showpost.php?p=38496806&postcount=11

ResponderCitar
Respondido : 03/09/2019 11:20 pm
RomanF
(@romanf)
Principiante

@rortega

Hallo Raul,
Thank you very much for help. Everything works. I will do the exact tests.
I didn't find the file because it had the same name as before. and ZIP replaced it. only earlier "spracingf3" was not remembered by me, it re-entered.

Is there an exact description of the u360 service? I would try to translate it.
Greetings to you and the whole team!

FoMa Systeme GmbH

ResponderCitar
Respondido : 04/09/2019 2:48 pm
rortega
(@rortega)
Miembro Moderator

@josean

No he probado a imprimir otro diseño, pero la oficial es quizás la más utilizada entre los que se inician, e incluso alguno quien se hacía su propia mecánica que se ha echo una.

ResponderCitar
Respondido : 04/09/2019 6:11 pm
rortega
(@rortega)
Miembro Moderator

@romanf

Some months ago I started rewrittin and moving all documentation to this wiki folder (the start page is index.md):

https://github.com/raul-ortega/u360gts/tree/master/wiki

Another great contribution would be creating the locales file for the configurator, for german language (translations):

https://github.com/raul-ortega/u360gts-configurator/blob/master/_locales/en/messages.json

 

This post was modified hace 2 meses by rortega
ResponderCitar
Respondido : 04/09/2019 6:38 pm
Página 6 / 8
Comparte:

Por favor Iniciar Sesión o Registro